How to do well in ink washing and color changing i

2022-09-21
  • Detail

How to do well in the offset printing process?

in the offset printing process, especially in the monochrome Offset printing machine, whether y, m, C, BK four-color printing, or trademark, packaging and decoration, it is often necessary to wash the ink and change the color, clean the ink transmission system of the whole offset printing machine, and then change it with new ink. The ink scraper of the ink washing device is composed of a rubber knife, an ink receiving slot and an adjusting screw

all seamless steel pipes need to be tested for mechanical properties. The ink washing process: pour gasoline and car wash water on the ink roller, install the ink scraper in the ink washing position slot, tighten the adjusting screw, make the rubber knife contact the surface of the inking roller corresponding to the offset press at an angle of 40, and the inking roller moves longitudinally and horizontally to scrape and wash the old ink and gasoline on the ink conveying system into the ink receiving slot through the rubber knife

the ink washing and color changing is clean and thorough, which plays a key role in the accurate grasp of the printing hue. Only by washing the ink prints can the hue be correct and the ink color be bright and accurate. In the actual ink washing and color changing operation, we should pay attention to the following points:

1 The ink scraper device for ink washing can only be installed on the offset press when the ink is washed and changed, or when the ink roller needs to be cleaned due to other factors. During installation, the eccentric pin shafts at both ends of the ink receiving tank are placed in the open groove of the support shaft fixed on the offset press wallboard, and the adjusting nut is fixed in the opening of the square iron block on the wallboard. Then start the offset press, and screw the adjusting nut, so that the blade of the rubber knife slowly contacts the surface of the inking roller. The contact pressure of the adjusting screws at the left and right ends is required to be uniform. The rubber knife contacts each part of the inking roller evenly, which can scrape the ink comprehensively

2. When cleaning the ink, in order to thoroughly and cleanly remove the ink accumulation and ink marks on all ink rollers, it is best to sprinkle gasoline on the ink roller near the ink bucket area from the upper part of the ink conveying part, so that the waste ink from the cleaning will flow into the ink receiving tank from the upper part of the rubber knife edge, and after a period of cleaning, the ink roller can be cleaned

3. After the ink roller and ink bucket of the ink conveying parts are cleaned, wipe them clean, and clean them with a clean, soft, tidy cloth head without fiber nap and with good water absorption performance

4. The installation position of the ink scraper of the cleaning and washing mechanism should be accurate, and the rubber blade and the surface of the inking roller should be kept at the same distance and the same contact pressure

5. After cleaning, take the wiping cloth steadily and wipe it quickly. Don't let the wiping cloth get involved in the ink roller when the offset press is running

6. When washing ink and changing color, the operator is required to sprinkle gasoline from the upper ink roller evenly and appropriately, and do not splash gasoline everywhere

7. Smoking and open flames are strictly prohibited in the workshop to prevent fires during ink washing and color changing

8. When the offset press is running, you must pay attention to safety when scrubbing the ink roller

① be careful that the cuffs, hands and corners of the jacket are entangled by the ink roller or roller, causing human injury

② it is forbidden to carry box rulers, keys, coins, pencils, pens and other hard objects, as well as ink shovels and repair machine tools in the pocket of the operator's work clothes to prevent them from falling into the ink roller and causing accidents

9. Generally, there are two situations for ink washing and color changing, one is to change light ink into dark ink, and the other is to change dark ink into light ink

① method of changing light ink into dark ink

it is easier to change light ink into dark ink, which saves time and effort for ink roller cleaning. First, use an ink shovel to shovel out the light colored ink from the ink bucket. As long as you use an ink scraper to clean up the light colored ink on the ink roller, and at the same time, clean up the ink skin, paper wool and other sundries left on the ink roller due to the low vitrification temperature of PBT

② replace dark ink with light ink

offset ink washing and color changing, and replace dark ink with light ink. At this time, the cleaning requirements for the ink roller are higher, and the cleaning is more difficult. The cleaning degree of the ink roller exceeds the ideal demand of the furnace for current. It requires that the light ink should not be polluted by the dark ink. If the old ink on the ink roller is not completely cleaned, the color and hue will be inaccurate, and there will be the shadow of dark ink in the light ink, Therefore, the ink bucket, ink roller, ink shovel, etc. must be cleaned, and then the ink shovel will be applied to the ink roller. Start the offset press, so that the light color ink is evenly stuck on the ink roller, and then pour gasoline to clean it. If it is not clean, make full use of the technical advantages of the military industrial unit stationed in Shandong, and you can also repeat it until the ink roller is clean

Copyright © 2011 JIN SHI